收藏本站
CDB5581
2. QUICK START
Signals to ADC & Mux
Buffer Enable
Calibrate 2
4.096 V Reference
DC Supply
ADC Reset
Master/Slave SPI
ADC MCLK Out
Analog Inputs
NOTES:
1. Shaded boxes marked with "OPT. CONFIG." are not necessary for operation in an end user product.
2. Calibration function has been removed from the device but still appears on the PCB. J2 must be shorted (grounded)
for proper operation. See Appendix E for details.
Figure 2. CDB5581 Board Layout
The CDB5581 evaluation board is designed to interface with a data acquisition system. To connect and
configure the CDB5581 perform the following initialization procedure:
1. Verify that the power supplies are off.
2. Connect the power supplies to the CDB5581 as shown in Table 1 on page 6.
3. Verify that the power is off to the analog input signal & control signal sources.
4. Connect the analog input signal source to the evaluation board per Table 2 on page 6. Verify from Table 4
on page 8 that the analog input channel selected is IN_A.
5. Configure the CDB5581 by connecting the control signal sources to the evaluation board as shown in
Table 3 on page 7. Apply logic-level inputs as required to override the resistor pull-ups/pull-downs.
6. Make connections to the SPI? serial port connector as shown in Table 5 on page 8. The CS5581 ADC
serial port is configured by default to operate in the SSC (Synchronous Self Clocking) mode. Refer to the
CS5581 data sheet for more information on serial communication modes and signal timing.
7. Turn on the power supplies to the evaluation board.
8. Apply power to the signal source.
9. Press the Reset switch on the evaluation board.
10. The CS5581 ADC's SPI? serial port should now be communicating data.
DS796DB3
5
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
CDK5571 CDB5571 W/CAPTURE PLUS 2 SYSTEM
CDK5581 KIT BOARD FOR CDB5581 ADC
CF1176-000 SHIELD TERMINATOR
SMS4SE4K9 集管和线壳 4P QIKMATE PIN STRT PC BOARDMOUNT
CF6147-000 CABLE TERMINATION
CF6153-000 HEAT SHRINK TUBING
22-56-6507 集管和线壳 CGrid SL Hsg Opt F D Hsg Opt F DR 50Ckt
CG4-LEJ/12 CARD LEVER/EJECTORS PACK OF 12
相关代理商/技术参数
CDB56-A 制造商:Panduit Corp 功能描述:
CDB572 制造商: 功能描述: 制造商:Rockwell Automation / Allen-Bradley 功能描述:
CDB5S-A-L 制造商:Panduit Corp 功能描述:
CDB6/2 功能描述:接线端子板接口模块 Feed-thru Term Dble level RoHS:否 制造商:Phoenix Contact 类型:Isolating Amplifier 节距: 位置/触点数量:2 线规量程: 电流额定值: 电压额定值:24 V 安装风格:DIN Rail 安装角: 端接类型:Screw 触点电镀:
CDB6/3 功能描述:接线端子板接口模块 lightning Arrestor 3pole RoHS:否 制造商:Phoenix Contact 类型:Isolating Amplifier 节距: 位置/触点数量:2 线规量程: 电流额定值: 电压额定值:24 V 安装风格:DIN Rail 安装角: 端接类型:Screw 触点电镀:
CDB6/4 功能描述:接线端子板接口模块 lightning Arrestor 3pole RoHS:否 制造商:Phoenix Contact 类型:Isolating Amplifier 节距: 位置/触点数量:2 线规量程: 电流额定值: 电压额定值:24 V 安装风格:DIN Rail 安装角: 端接类型:Screw 触点电镀:
CDB6/4-R 功能描述:接线端子板接口模块 lightning Arrestor 3pole RoHS:否 制造商:Phoenix Contact 类型:Isolating Amplifier 节距: 位置/触点数量:2 线规量程: 电流额定值: 电压额定值:24 V 安装风格:DIN Rail 安装角: 端接类型:Screw 触点电镀:
CDB6059-1 功能描述:WM8725, WM8761 - Audio, Stereo DAC Evaluation Board 制造商:cirrus logic inc. 系列:- 零件状态:有效 主要用途:音频，立体声 DAC 嵌入式:- 使用的 IC/零件:WM8725, WM8761 主要属性:- 辅助属性:- 所含物品:板 标准包装:1